[ivtv-devel] Unidentified card: Posting dmesg info as instructed.

[Marc Thompson]

I am not a mailing list member.

Dear IVTV Developers,

I have a card that is identified by ivtv as a PVR-250.    I have
not had success with it yet.  I have not yet used GATOS drivers.

dmesg output requested posting the IVTV init information to this
mailing list address.

I would appreciate any assistance.  I cannot identify the subvendor
PCI id for the Theater200 chip.

Best Regards.
marcthomp*@* g mai   l      .com

Physical description:
PCI Bus.
No audio input/output jacks on board.
external inputs:  Composite, S-Video, CATV, audio (mini-jack)

Chips/info on circuit board:
Philips:       3139  14718921D#            FI1236/W H-3
Conexant CX23416-12  MPEG II A/V Encoder
ATI Theater200  213T20ZQA12
printed on board:  PN 109-A3800-01
kernel: ivtv:  ==================== START INIT IVTV ====================
kernel: ivtv:  version 0.4.1 (tagged release) loading
kernel: ivtv:  Linux version: 2.6.13-1.1526_FC4 686 REGPARM 4KSTACKS gcc-4.0
kernel: ivtv:  In case of problems please include the debug info between
kernel: ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
kernel: ivtv:  any module options, when mailing the ivtv-users mailinglist.
kernel: ivtv0: Unknown card: vendor/device: 4444/0016
kernel: ivtv0:               subsystem vendor/device: 1002/fffb
kernel: ivtv0:               cx23416 based
kernel: ivtv0: Defaulting to WinTV PVR 250 card
kernel: ivtv0: Please mail the vendor/device and subsystem
vendor/device IDs and what kind of
kernel: ivtv0: card you have to the ivtv-devel mailinglist (www.ivtvdriver.org)
kernel: ivtv0: Prefix your subject line with [UNKNOWN CARD].
kernel: ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKA] -> GSI 11
(level, low) -> IRQ 11
kernel: ivtv0 warning: i2c client addr: 0x50 not found for command 0x0!
kernel: ivtv0: Error -19 reading Hauppauge eeprom.
kernel: ivtv0: Possible causes: the tveeprom module was not loaded, or
kernel: ivtv0: the eeprom kernel module was loaded before the tveeprom module.
kernel: ivtv0 warning: i2c client addr: 0x21 not found for command 0x8004646b!
kernel: ivtv0: Could not detect tuner standard, defaulting to NTSC.
kernel: ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
kernel: ivtv0: Encoder revision: 0x02050032
kernel: ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers
(4096KB total)
kernel: ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers
(2048KB total)
kernel: ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers
(2048KB total)
kernel: ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608
buffers (2048KB total)
kernel: ivtv0 warning: i2c client addr: 0x21 not found for command 0x40085618!
kernel: ivtv0 warning: i2c client addr: 0x21 not found for command 0xc0045627!
kernel: ivtv0 warning: i2c client addr: 0x40 not found for command 0x40086d11!
kernel: ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610!
kernel: ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611!
kernel: ivtv0 warning: i2c client addr: 0x00 not found for command 0x40085618!
kernel: ivtv0 warning: i2c client addr: 0x40 not found for command 0x40085618!
kernel: ivtv0 warning: i2c client addr: 0x21 not found for command 0x40085618!
kernel: ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610!
kernel: ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611!
kernel: ivtv0 warning: i2c client addr: 0x21 not found for command 0x40045613!
kernel: ivtv0 warning: i2c client addr: 0x00 not found for command 0x402c5639!
kernel: ivtv0 warning: i2c client addr: 0x40 not found for command 0x402c5639!
kernel: ivtv0 warning: i2c client addr: 0x21 not found for command 0x40045612!
kernel: ivtv0 warning: i2c client addr: 0x40 not found for command 0x80287610!
kernel: ivtv0 warning: i2c client addr: 0x40 not found for command 0x40287611!
kernel: ivtv0: Initialized WinTV PVR 250, card #0
kernel: ivtv:  ====================  END INIT IVTV  ====================